MICROPOLIS 1684-7 HARD DISK DRIVE REPAIR, MICROPOLIS 1684-7 SCSI HARD DISK DRIVE REPAIR, SPECIFICATIONS, JUMPERS,
micropolis 1684-7 hard disk drive specifications, Micropolis 1684-7 Hard Disk Drive Specifications, Jumpers,
micropolis 1684-7 hard disk drive repair, Micropolis 1684-7 Hard Disk Drive Repair,
micropolis 1684-7 hard disk drive specs, Micropolis 1684-7 Hard Disk Drive Specs,
micropolis 1684-7 hard disk drive repair, Micropolis 1684-7 Hard Disk Drive Repair Micropolis 1684-7
Specifications



micropolis 1684-7 picture.
micropolis 1684-7 picture.
micropolis 1684-7 picture.

Micropolis 1684-7 Specifications
Model Capacity Size Height Bus Type Int.Type
Micropolis 1684-7 340MB 5.25" HHT SCSI2 SE

Size 5-1/4"
Interface SCSI
Encoding Method  
Formatted Capacity 339.6 MB
Disks 4
Heads 7
Cylinders 1780
Sectors 54
Buffer Size N/A
Average Seek 14 msec
Single Track 4 msec
Rotation Speed / Avg. Latency 3600 rpm +/- 0.5%
Transfer Rate to / from media 15 Mbits / sec
Transfer Rate to / from buffer N/A
Tracks Per Inch (TPI)  
Bits Per Inch (BPI)  
Dimensions 8.0"L x 5.75"W x 1.625"H
Weight 5.75 lbs.


POWER REQUIREMENTS
  +12V +/-5% +5V +/-5% Power
Spin up 2.0A (max)    
Read / Write .9A avg .8A avg  
Typical     14.8 Watts

Notes:
Drive Addressing and Interface Termination



ID0, ID1, ID2 SCSI Address Jumpers
  The SCSI ID (drive address) jumpers are identified as ID0, ID1, and ID2.
  ID selection is binary, as shown in the table below.


SCSI
Address
Jumpers
ID2 ID1 ID0
0 out out out
1 out out in
2 out in out
3 out in in
4 in out out
5 in out in
6 in in out
7 in in in

  For multiple drive installations, on one Host Adapter, each drive must
  have a unique address. Drives are configured as SCSI ID 0 at the factory.

RN9 Interface Terminator
  The Interface Terminators factory installed at RN9 provides proper
  termination for the interface lines. When daisy-chaining multiple drives,
  leave the terminator installed only in the last physical drive (or drives)
  on the daisy chain cable; remove the terminator from each of the other
  drives (or the host computer).

W1, W2 Terminator Option
  W1 and W2 selects the source of terminator power (+5V) for the interface
  terminators. When a jumper is installed at W1(the factory default configuration)
  and no jumper is installed at W2 the drive provides terminator power. This
  configuration is used for PC/AT applications. If a jumper is installed at W2,
  terminator power is provided by the host system via interface cable J1, pin 26.
  If a jumper is installed at W2 and W31, the drive provides terminator power to
  its on-board terminators and also to the SCSI bus via interface cable J1.

W31 Bus Option
  W31 allows the drive to supply interface terminator power to the SCSI Bus.
  If W31 is not installed (the factory default configuration), the drive does not
  supply SCSI bus interface terminator power. W31 should not be installed for
  PC/AT applications.

W3, Spindle Option
  W3 selects the spindle control option. If W3 is installed, the drive waits for a
  Start Spindle command (after power is applied) to start the spindle motor.
  If W3 is not installed (the factory default configuration), the drive automatically
  starts the spindle motor at power-on. W3 is not installed for PC/AT installations.

W9 Bus Parity Option
  W9 selects the parity check option. If W9 is installed, the drive neither generates
  nor detects parity. If W9 is not installed (the factory default configuration), the drive
  generates parity and enables parity detection. W9 is usually not installed for PC/AT
  applications. Verify the correct configuration required by your Host Adapter.

All manufacturer's Names, Logos and trademarks are the properties of the respective manufacturer.


HOME Micropolis Drive Specs All Hard Drives TOP


Check our Media Store for all your Floppy Disk and Tape Supplies.


Contact us

Copyright 1997 - 2011 Erv Fleckstein ( M. Farris & Associates ). All Rights Reserved.