MICROPOLIS 1908-15 HARD DISK DRIVE REPAIR, MICROPOLIS 1908-15 SCSI HARD DISK DRIVE REPAIR, SPECIFICATIONS, JUMPERS,
micropolis 1908-15 hard disk drive specifications, Micropolis 1908-15 Hard Disk Drive Specifications, Jumpers,
micropolis 1908-15 hard disk drive repair, Micropolis 1908-15 Hard Disk Drive Repair,
micropolis 1908-15 hard disk drive specs, Micropolis 1908-15 Hard Disk Drive Specs,
micropolis 1908-15 hard disk drive repair, Micropolis 1908-15 Hard Disk Drive Repair Micropolis 1908-15
Specifications



micropolis 1908-15 picture.
micropolis 1908-15 picture.
micropolis 1908-15 picture.

Micropolis 1908-15 Specifications
Model Capacity Size Height Bus Type Int.Type
Micropolis 1908-15 1408MB 5.25" FHT SCSI2 SE

Size 5-1/4"
Interface SCSI-2
Encoding Method  
Formatted Capacity 1408 MB
Disks 8
Heads 15
Cylinders 2112
Sectors Variable
Buffer Size N/A
Average Seek 11.5 msec
Single Track 2.5 msec.
Rotation Speed / Avg. Latency 5400 rpm +/- 0.5%
Transfer Rate to / from media 10 Mbytes / sec Synchronous
Transfer Rate to / from buffer N/A
Tracks Per Inch (TPI)  
Bits Per Inch (BPI)  
Dimensions 8.0"L x 5.75"W x 3. 25"H
Weight 5.75 lbs.


POWER REQUIREMENTS
  +12V +/-5% +5V +/-5% Power
Spin up 2.0A    
Read / Write 4.3 max 1.5A  
Typical     24 watts

Notes:
Drive Addressing and Interface Termination



ID0, ID1, ID2 SCSI Address Jumpers
  The SCSI ID (drive address) jumpers are identified as ID0, ID1, and ID2.
  ID selection is binary, as shown in the table below.


SCSI
Address
Jumpers
ID2 ID1 ID0
0 out out out
1 out out in
2 out in out
3 out in in
4 in out out
5 in out in
6 in in out
7 in in in

  For multiple drive installations, on one Host Adapter, each drive must have
  a unique address. Drives are configured as SCSI ID 7 at the factory.

RN6 Interface Terminator
  The Interface Terminator factory installed at RN6 provides proper termination
  for the interface lines. When daisy-chaining multiple drives, leave the
  terminator installed only in the last physical drive (or drives) on the daisy
  chain cable; remove the terminator from each of the other drives
  (or the host computer).

Bus Termination Power Option
  A jumper is installed at W1, at W2, or at W2 and W12 to select the
  source of terminator power (+5V) for the SCSI Bus terminator packs on
  the device electronics board.

  DO NOT INSTALL JUMPERS AT BOTH W1 AND W12

  When a jumper is installed at W1(the factory default configuration), 
  the drive provides terminator power to it's on-board terminators.

  When a jumper is installed at W2 , terminator power is is provided by
  the host system via the interface cable J1, pin 26 (TERMPWR).

  When a jumper is installl at both W2 and W12, the drive provides
  terminator power to its on-board terminators and also to the SCSI bus
  via interface cable J1,pin 26(TERMPWR).

Frame Ground Options
  Jumper W11 selects the frame ground option.

  When W11 is installed, the drive's frame is connected to frame ground.

  When a jumper is not installed at W11 (the factory default
  configuration), frame ground is not connected to logic ground.

Spindle Control Options
  A jumper bridging pins 7 and 8 of J2 (the 4th set of pins) is used to
  select the spindle control option.

  When a jumper is installed, the drive must wait for an interface Start
  Unit command to start the spindle motor.

  When a jumper is not installed (the factory default configuration),
  the drive automatically starts the spindle motor at power-on

Write Protect Option
  A jumper bridging pins 11 and 12 of J2 (the 6th set of pins) is used
  to select the write protect option.

  When a jumper is installed, the drive is write protected. CAUTION: The
  drive can still be formatted.

  When a jumper is not installed, (the factory default configuration),
  the drive is not write protected.

Bus Parity Option
  A jumper bridging pins 13 and 14 of J2(7th set of pins) is used to
  select the parity check option.

  When a jumper is installed, the drive generates parity but does not detect
  parity.

  When a jumper is not installed, (the factory default configuration), the
  drive generates parity and enables parity detection.

Spindle Synchronization Option
  The Rotational Position Locking field (MODE SELECT command, Page Code 04h)
  is used to specify spindle synchronization operation; see document #110366
  (Scsi Implementation in Micropolis "MZR" Products) and ANSI SCSI Standard.

  Unsynchronized: If the drive is set to Unsynchronized (PRL=00b), it ignores the
  SLAVE SYNC signal.

  Slave: If the drive is set to Slave (RPL=01b), it does not generate the MASTER SYNC
  signal or the SLAVE SYNC signal but synchronizes its index to the SLAVE SYNC
  signal (J2,pin 20) supplied by an external source.

  Master: If the drive is set to MASTER (RPL=10b), it generates the SLAVE SYNC
  output signal (j2,pin 20) for use directly by the slave drives.

  Master Control: If the drive is set to Master Control (RPL=11b), it generates the
  MASTER SYNC signal(j2,pin 20). This output is used by the controller to
  generate the SLAVE SYNC signal(J2,pin 20) for the slave drives.

  **** THESE SPECIFICATIONS ARE PRELIMINARY.

All manufacturer's Names, Logos and trademarks are the properties of the respective manufacturer.


HOME Micropolis Drive Specs All Hard Drives TOP


Check our Media Store for all your Floppy Disk and Tape Supplies.


Contact us

Copyright 1997 - 2011 Erv Fleckstein ( M. Farris & Associates ). All Rights Reserved.