|Micropolis 1991AV Specifications|
|Micropolis 1991AV Gold Series||9091MB||5.25"||FHT||SCSI2||Fast|
|Formatted Capacity||9090 MB|
|Average Seek||12 msec|
|Single Track||5.56 msec|
|Rotation Speed / Avg. Latency||5400 rpm +/- 0.5%|
|Transfer Rate to / from media||10 Mbytes / sec Synchronous|
|Transfer Rate to / from buffer||N/A|
|Tracks Per Inch (TPI)|
|Bits Per Inch (BPI)|
|Dimensions||8.0"L x 5.75"W x 3. 25"H|
|+12V +/-5%||+5V +/-5%||Power|
|Read / Write||4.8A||1.0A|
|Typical seeking||33 Watts|
Drive Addressing and Interface Termination
For multiple drive installations, on one Host Adapter, each drive must
have a unique address. Drives are configured as SCSI ID 7 at the factory.
RN4 & RN5 Interface Terminators
The Interface Terminator factory installed at RN6 provides proper termination
for the interface lines. When daisy-chaining multiple drives, leave the terminator
installed only in the last physical drive (or drives) on the daisy chain cable;
remove the terminator from each of the other drives (or the host computer).
Bus Termination Power Option
A jumper is installed at W6, at W8, or at W5 to select the source of terminator
power (+5V) for the SCSI Bus terminator packs on the device electronics board.
When a jumper is installed at W6 (the factory default configuration), the drive
provides terminator power to it's on-board terminators.
When a jumper is installed at W8 , terminator power is is provided by the host
system via the interface cable J1, pin 26 (TERMPWR).
When a jumper is installed at both W8 and W5, the drive provides terminator
power to its on-board terminators and also to the SCSI bus via interface cable J1,
Frame Ground Options
Jumper W9 selects the frame ground option.
When W9 is installed, the drive's frame is connected to frame ground.
When a jumper is not installed at W9 (the factory default configuration), frame
ground is not connected to logic ground.
Spindle Control Options
A jumper bridging pins 7 and 8 of J2 (the 4th set of pins) is used to select the
spindle control option.
When a jumper is installed, the drive must wait for an interface Start Unit
command to start the spindle motor.
When a jumper is not installed (the factory default configuration), the drive
automatically starts the spindle motor at power-on.
A jumper at WP selects SCSI-1 or SCSI-2. If the jumper is installed
(the factory default configuration), the drive is configured as a SCSI-2 device.
the drive is not write protected.
Bus Parity Option
A jumper bridging pins 13 and 14 of J2(7th set of pins) is used to select the
parity check option.
When a jumper is not installed, (the factory default configuration), the drive
generates parity and enables parity detection.
When a jumper is installed, the drive neither generates nor detects parity.
Spindle Synchronization Option
The Rotational Position Locking field (MODE SELECT command, Page Code 04h)
is used to specify spindle synchronization operation; see document #110366
(Scsi Implementation in Micropolis "MZR" Products) and ANSI SCSI Standard.
Unsynchronized: If the drive is set to Unsynchronized (PRL=00b), it ignores the
SLAVE SYNC signal.
Slave: If the drive is set to Slave (RPL=01b), it does not generate the MASTER SYNC
signal or the SLAVE SYNC signal but synchronizes its index to the SLAVE SYNC
signal (J2,pin 20) supplied by an external source.
Master: If the drive is set to MASTER (RPL=10b), it generates the SLAVE SYNC
output signal (j2, pin 20) for use directly by the slave drives.
Master Control: If the drive is set to Master Control (RPL=11b), it generates the
MASTER SYNC signal(j2,pin 20). This output is used by the controller to generate
the SLAVE SYNC signal(J2,pin 20) for the slave drives.
|HOME||Micropolis Drive Specs||All Hard Drives||TOP|