MICROPOLIS 3391WD Tomahawk HARD DISK DRIVE REPAIR, MICROPOLIS 3391WD Tomahawk SCSI HARD DISK DRIVE REPAIR, SPECIFICATIONS, JUMPERS,
micropolis 3391WD Tomahawk hard disk drive specifications, Micropolis 3391WD Tomahawk Hard Disk Drive Specifications, Jumpers,
micropolis 3391WD Tomahawk hard disk drive repair, Micropolis 3391WD Tomahawk Hard Disk Drive Repair,
micropolis 3391WD Tomahawk hard disk drive specs, Micropolis 3391WD Tomahawk Hard Disk Drive Specs,
micropolis 3391WD Tomahawk hard disk drive repair, Micropolis 3391WD Tomahawk Hard Disk Drive Repair Micropolis 3391WD
Specifications



micropolis 3391wd picture. micropolis 3391wd picture.
micropolis 3391wd picture.

Micropolis  3391WD Specifications
Model Capacity Size Height Bus Type Int.Type
Micropolis 3391WD Tomahawk 9 9100MB 3.5" HHT SCSI3 D/W

Size 3 1/2" 
Interface ULTRA SCSI-3
Encoding Method  
Formatted Capacity 9.1 GB
Disks  
Heads  
Cylinders 4811
Sectors Variable
Buffer Size N/A
Average Seek 7.9 msec
Single Track  
Rotation Speed/Avg. Latency 7200 rpm +/- 0.5%
Transfer Rate to / from. media 20 Mbytes/sec  Synchronous
Transfer Rate to / from buffer  
Tracks Per Inch (TPI)  
Bits Per Inch (BPI)   
Dimensions 5.75"D x 4.0"W x 1.625"H
Weight 0.00 lbs.

POWER REQUIREMENTS
  +12V +/-5% +5V +/-5% Power
Spin up .7A     
Read / Write 2.4A 1.1A  
Typical seeking       17 Watts

Notes:

Configuration Options

SCSI ID
Jumpers at Pin 3-4, 5-6, 7-8, & 9-10 select the SCSI ID.
Each SCSI device on one Host Adapter must have a unique SCSI ID (0-15). 
SCSI ID0 is the Default.

SCSI ID Pin
9-10
Pin
7-8
Pin
5-6
Pin
3-4
0 (Default) out out out out
1 out out out in
2 out out in out
3 out out in in
4 out in out out
5 out in out in
6 out in in out
7 out in in in
8 in out out out
9 in out out in
10 in out in out
11 in out in in
12 in in out out
13 in in out in
14 in in in out
15 in in in in


Interface Termination
An external terminator provides termination for the interface lines.
Suggested end-of-cable terminator: Methode DS2050-01-68D.

+5V to BUS (W3)
Jumper installed at W3 (Default) - Drive provides terminator power (TERMPWR)
  to the SCSI Bus.
Jumper omitted at W3 - Host system provides TERMPWR.

Spindle Control (SP0)
Jumper installed at SP0, jumper omitted at SP1 - Spindle motor starts when 
  SCSI ‘START UNIT’ command is received.
Jumpers omitted at SP0 (Default) and at SP1 - Spindle motor starts at power-on.

Spindle Delay (SP1)
Jumper installed at SP1, jumper omitted at SP0 - Spindle motor start-up delayed
   based on SCSI ID (12 seconds per SCSI ID).
Jumpers omitted at SP1 (Default) and at SP0 - Spindle motor starts at power-on.


Write Protect (WP)
Jumper installed at WP - Drive is write protected.
Jumper omitted at WP (Default) - Drive is not write protected.

BUS Parity Check (PTY)
Jumper installed at PTY - Drive neither generates nor detects parity.
Jumper omitted at PTY (Default) - Drive generates parity and has parity detection enabled.

Remote LED
Open-collector output - Used to drive a user-supplied LED to indicate the drive is active.

All manufacturer's Names, Logos and trademarks are the properties of the respective manufacturer.


HOME Micropolis Drive Specs All Hard Drives TOP


Check our Media Store for all your Floppy Disk and Tape Supplies.


Contact us

Copyright © 1997 - 2011 Erv Fleckstein ( M. Farris & Associates ). All Rights Reserved.